Leslie Green Tube Station

Quoting Wiki, about Leslie Green:

In 1903 he was appointed as architect for the Underground Electric Railways Company of London (UERL) to design stations for three underground railway lines then under construction – the Great Northern, Piccadilly and Brompton Railway (GNP&BR), the Baker Street and Waterloo Railway (BS&WR) and the Charing Cross, Euston and Hampstead Railway (CCE&HR), which, respectively, became parts of the present day Piccadilly line, Bakerloo line and Northern line. Green was commissioned to design 50 new stations, including their external appearance, and internal fittings and decoration.

Many of his stations remain in pretty much their original state.

Earl's Court


Leicester Square


Covent Garden


Russell Square


Aldwych (originally Strand)


And so the models. I did Aldwych pretty faithfully, based on Google Street View. The gate has since been boarded up apparently.


Available on Cults here: https://cults3d.com/en/3d-model/game/aldwych-station-strand-entrance

I then created a set of pieces that could be put together in various configurations.




I also did a corner piece, and put some bits together.



Available on Cults here: https://cults3d.com/en/3d-model/game/leslie-green-underground-station

If Leslie Green is not your thing, an alternative entrance to Leicester Square.


And the model:


Available on Cults here: https://cults3d.com/en/3d-model/game/basic-tube-station-leicester-square






Comments

Post a Comment

Popular posts from this blog

Introduction to the Blog

 My first post was back in February - before I had even purchased a 3d printer, and it is now November and I am writing the introduction... This blog is all about my experiences for 3d printing. It is a way for me to share what I learn along the way, and to show off what I have created. Most pages are tagged Model and are about a specific model, and the prototype it is based on. Generally I try to visit the prototype, and include a couple of photos of that for comparison. I also try to learn the history of the building, which is not always easy, and record that on the page too. A lot are buildings in and around Preston, as that is where I live. Models are further divided into Building , Railway (i.e., railway-related buildings), Feature (bridges, tunnel portals, etc.), Rolling Stock , Vehicle and Clutter (smaller items) In addition, there are pages tagged How to and Prototype . If you want to know how to use Blender to make 3d models, there is an article I wrote on another s...
Read more

Bad normals

Image
This is an issue I hit whilst revising Lund Church. A model is made up of polygons, and each polygon has a front and a back. In Blender it is not obvious which is which, though Blender does track it. And occasionally it gets it wrong, and a section of mesh is, in effect, inside-out. When you try to print out, there is just a hole there. In the image below you can see some of the stones to the left of the windows are not just missing but also caused holes in the superstructure. Microsoft 3D Builder does not spot it, all looks good in there. But Chitubox does. It will not actually say anything or stop you producing a bad file, but it does highlight bad bits in your model. In the image below, all that roof is wrong, the right side of the arches, a part of the cross at the end of the roof, and some stones in the tower. All are shown in a much darker colour. So what are normals? Behind the scenes Blender creates a vector (essentially a line) that starts from the centre of the polygon and ex...
Read more

Array in a Circle with Blender

Image
Blender's Array modifier lets you repeat an object any number of times. I only recently discovered this can be in a circle - previously I have done that with Geometry Nodes, which is far more complicated. NOTE: Blender 5 has an alternative methods. See here . In A Line The Array modifier's most obvious use is to repeat an object in a row. You want a row of identical houses? Create one (as a single object!), and add an Array modifier. Want a brick wall? Create two (one staggered above the other), and add two Array modifiers, one in the X direction and one in the Z. You can do this as a "Relative Offset" or a "Constant Offset". With relative offset, the distance between each one is determined by the item size in that direction multiplied by the value. With constant offset the item size does not matter - except that the size transform is applied after the modifier, so it can feel like it does. If you need a specific spacing, constant offset can be better; just ...
Read more